wpa_cli

WPA command-line client for interacting with wpa_supplicant

Syntax:

wpa_cli  [-p path to ctrl sockets] 
         [-i ifname] 
         [-hvB] [-a action file] 
         [-P pid file] [command ... ]

Runs on:

Neutrino

Options:

-p path

Change the path where control sockets should be found.

-i ifname

Specify the interface that is being configured. By default, choose the first interface found with a control socket in the socket path.

-h

Help. Show a usage message.

-v

Show version information.

-B

Run as a daemon in the background.

-a file

Run in daemon mode executing the action file based on events from wpa_supplicant. The specified file will be executed with the first argument set to the interface name, and the second to CONNECT or DISCONNECT, depending on the event.

-P file

Set the location of the PID file.

command

Run a command; see “Supported commands,” below.

Description:

The wpa_cli utility is a text-based front-end program for interacting with wpa_supplicant. You can use it to query the current status, change the configuration, trigger events, and request interactive user input.

The wpa_cli utility can show the current authentication status, selected security mode, dot11 and dot1x MIBs, etc. In addition, it can configure some variables like EAPOL state machine parameters and trigger events like reassociation and IEEE 802.1X logoff/logon.

The wpa_cli utility provides a user interface to request authentication information, such as user name and password, if these aren't included in the configuration. You can use this to implement, for example, one-time passwords or generic token card authentication where the authentication is based on a challenge-response that uses an external device for generating the response.

You can configure the control interface of wpa_supplicant to allow non-root user access (ctrl_interface_group in the configuration file). This makes it possible to run wpa_cli with a normal user account.

The wpa_cli utilities supports interactive and command-line modes. Both modes share the same command set, and the main difference is in interactive mode providing access to unsolicited messages (event messages, user name/password requests).

If you don't specify a command when you start wpa_cli, the utility goes into interactive mode. You then enter commands at the wpa_cli prompt.

Supported commands

The wpa_cli utility currently supports the following commands:

add_network

Add a network.

bssid network_id BSSID

Set the preferred BSSID for an SSID.

disable_network network_id

disable a network

disconnect

Disconnect and wait for a reassociate command before connecting.

enable_network network_id

Enable a network.

get_capability eap/pairwise/group/key_mgmt/proto/auth_alg

Get capabilities.

get_network network_id variable

Get network variables.

help

Display usage information.

identity network_id identity

Configure the identity for an SSID.

interface [ifname]

Show interfaces or select the specified interface.

level debug_level

Change the debugging level.

license

Show the full wpa_cli license.

list_networks

List the configured networks.

logoff

IEEE 802.1X EAPOL state machine logoff.

logon

IEEE 802.1X EAPOL state machine logon.

mib

Get MIB variables (dot1x, dot11)

new_password network_id password

Change the password for an SSID.

otp network_id password

Configure a one-time password for an SSID.

passphrase network_id passphrase

Configure a private key passphrase for an SSID.

password network_id password

Configure a password for an SSID.

pin network_id pin

Configure a pin for an SSID.

pmksa

Show the PMKSA cache.

preauthenticate BSSID

Force preauthentication.

quit

Exit wpa_cli

reassociate

Force a reassociation.

reconfigure

Force wpa_supplicant to reread its configuration file.

remove_network network_id

Remove a network.

save_config

Save the current configuration.

scan

Request a new BSS scan.

scan_results

Get the latest scan results.

select_network network_id

Select a network (disable others).

set

Set variables (shows list of variables when run without arguments).

set_network network_id variable value

Set network variables (shows list of variables when run without arguments).

status [verbose]

Get the current WPA/EAPOL/EAP status.

terminate

Terminate wpa_supplicant.

See also:

wpa_supplicant

WiFi Configuration Using WPA and WEP in the Core Networking User's Guide