Warning: main(/www/www/htdocs/style/globals.php) [function.main]: failed to open stream: No such file or directory in /www/www/docs/6.4.1/neutrino/utilities/d/devn-micrel8841.so.html on line 1

Warning: main() [function.include]: Failed opening '/www/www/htdocs/style/globals.php' for inclusion (include_path='.:/www/www/common:/www/www/php/lib/php') in /www/www/docs/6.4.1/neutrino/utilities/d/devn-micrel8841.so.html on line 1

Warning: main(/www/www/htdocs/style/header.php) [function.main]: failed to open stream: No such file or directory in /www/www/docs/6.4.1/neutrino/utilities/d/devn-micrel8841.so.html on line 8

Warning: main() [function.include]: Failed opening '/www/www/htdocs/style/header.php' for inclusion (include_path='.:/www/www/common:/www/www/php/lib/php') in /www/www/docs/6.4.1/neutrino/utilities/d/devn-micrel8841.so.html on line 8

devn-micrel8841.so

Driver for Micrel 8841 (1 port) or 8842 (2 port) Ethernet controllers

Syntax:

io-pkt-variant -d micrel8841 [option[,option ...]] ... &

where variant is one of v4, v4-hc, or v6-hc.

Runs on:

Neutrino

Options:


Note: Use commas, not spaces, to separate the options.

did=0xXXXX
The PCI device ID.
duplex=0|1
Half (0) or full (1) duplex mode. The default is automatically detected on supported hardware. If you specify duplex, specify speed as well; if duplex alone is specified, it is ignored and both speed and duplex are autonegotiated.
multicast
Enable the receipt of all multicast packets, all ports. By default, the receipt of multicast packets is disabled.
pci=0xXXXX
The PCI index of the controller.
port0=num
1 means power down port 0 PHY (the default is 0, power on).
port1=num
1 means power down port 1 PHY (the default is 0, power on) on the 8842 (2 port).
priority=N
The priority of the driver's event thread. The default is 21.
promiscuous
Allow the driver to pass all data packets received, regardless of the address. By default, promiscuous mode is disabled.
receive=num
The number of Rx descriptors (and 2 KB npkts) to allocate. The default is 256.
speed=10|100
Set the link speed (specified in Mbits/second: 10 or 100).
switch
Enable switch mode on the 2-port 8842.

Note: This is very dangerous if you loop the network because of the resulting packet storms.

transmit=num
The number of Tx descriptors to allocate (the default is 256).
verbose
verbose=N
Be verbose. Specify num for more verbosity (num can be 1-4; the higher the number, the more detailed the output). The default is 0. The output goes to slogger; invoke sloginfo to view it.
vid=0xXXXX
The PCI vendor ID.

Description:

The devn-micrel8841.so driver controls Micrel 8841 (1 port) or 8842 (2 port) Ethernet controllers. This is a legacy io-net driver; its interface names are in the form enX, where X is an integer.

This driver supports hardware checksum calculations for both Tx and Rx of IP and TCP packets (UDP isn't supported). To enable hardware checksumming, use ifconfig like this, after starting the driver:

ifconfig enX ip4csum tcp4csum

Examples:

Start io-pkt-v6-hc using the devn-micrel8841.so driver and Qnet with 1024 transmit descriptors, and 1024 receive descriptors to avoid packet loss due to scheduling latency on slow processors:

io-pkt-v6-hc -d micrel8841 transmit=1024,receive=1024 -p qnet

Files:

/dev/io-net
The directory where, by default, drivers and protocol modules add entries. For more information, see the documentation for io-pkt*.

See also:

devn-*, devnp-*, ifconfig, io-pkt*


Warning: main(/www/www/htdocs/style/footer.php) [function.main]: failed to open stream: No such file or directory in /www/www/docs/6.4.1/neutrino/utilities/d/devn-micrel8841.so.html on line 221

Warning: main() [function.include]: Failed opening '/www/www/htdocs/style/footer.php' for inclusion (include_path='.:/www/www/common:/www/www/php/lib/php') in /www/www/docs/6.4.1/neutrino/utilities/d/devn-micrel8841.so.html on line 221