Warning: main(/www/www/htdocs/style/globals.php) [function.main]: failed to open stream: No such file or directory in /www/www/docs/6.4.1/neutrino/utilities/d/devn-i82544.so.html on line 1
Warning: main() [function.include]: Failed opening '/www/www/htdocs/style/globals.php' for inclusion (include_path='.:/www/www/common:/www/www/php/lib/php') in /www/www/docs/6.4.1/neutrino/utilities/d/devn-i82544.so.html on line 1
Warning: main(/www/www/htdocs/style/header.php) [function.main]: failed to open stream: No such file or directory in /www/www/docs/6.4.1/neutrino/utilities/d/devn-i82544.so.html on line 8
Warning: main() [function.include]: Failed opening '/www/www/htdocs/style/header.php' for inclusion (include_path='.:/www/www/common:/www/www/php/lib/php') in /www/www/docs/6.4.1/neutrino/utilities/d/devn-i82544.so.html on line 8
Driver for Intel Gigabit Ethernet LAN adapters and I/O Controller Hubs
io-pkt-variant -d /lib/dll/devn-i82544.so
[option[,option ...]] ... &
where variant is one of v4, v4-hc, or
v6-hc.
|
If you don't specify the full path to devn-i82544.so,
io=pkt* starts
devnp-i82544.so. |
Neutrino
|
Use commas, not spaces, to separate the options. |
- did=0xXXXX
- Detect only devices with the given PCI device ID.
The default is automatically detected on supported hardware.
- duplex=0|1
- Half (0) or full (1) duplex mode. The default is automatically
detected on supported hardware.
If you specify duplex, specify speed as well;
if you specify duplex alone, it's ignored, and both speed and
duplex are auto-negotiated.
- flowcontrol=0|1
- Disable (0) or enable (1) hardware flow control.
- irq=N
- IRQ of the interface. The default is automatically detected on supported
hardware.
- mac=XXXXXXXXXXXX
- MAC address of controller. The default is
automatically detected on supported hardware.
- mtu=X
- Maximum transmission unit. The default (1514) is
automatically detected on supported hardware.
- nomulticast
- Disable the driver from sending or receiving multicast
packets. By default, multicast is enabled.
- pauseignore
- Ignore pause frames with respect to full duplex flow control.
- pausesuppress
- Suppress pause frames with respect to full duplex flow control.
- pci=0xXXXX
- Detect devices only at this specific PCI index.
- priority=X
- Priority of the driver's event-handler thread. The default is
21.
- promiscuous
- Enable promiscuous mode. The default is off.
- receive=num
- Set the number of receive descriptors.
The default is 64 on PPC, and 128 on other platforms.
- speed=10|100|1000
- Media data rate (10Mbit, 100Mbit, or Gigabit operation). The default is
automatically detected on supported hardware.
If you specify speed, specify duplex as well;
if you specify speed alone, the specified speed is correctly set,
but duplex defaults to half (0).
- transmit=num
- Set the number of transmit descriptors.
The default is 64 on PPC, and 512 on other platforms.
- verbose
verbose=num
- Be verbose. Specify num for more verbosity (num can be 1-4; the higher
the number, the more detailed the output).
The output goes to slogger;
invoke sloginfo to view it.
- vid=0xXXXX
- Detect only devices with this specific PCI vendor ID.
The devn-i82544.so driver manages the Intel
82540, 82541, 82542, 82543, 82544, 82545, 82546, 82547, 82571, 82572, and
82573 Gigabit Ethernet LAN adapters,
and the ICH8 and ICH9 I/O Controller Hubs.
This is a legacy io-net driver;
its interface names are in the form enX, where
X is an integer.
|
If the device enumerators (see
enum-devices)
don't recognize your device, try explicitly specifying
the device ID with the did option when you start the driver. |
Some devices support hardware checksums, although some might do so in
only one direction; to determine if your device does, type:
ifconfig enX
and look for the following in the list of supported options:
- ip4csum, ip4csum-rx, ip4csum-tx
- tcp4csum, tcp4csum-rx, tcp4csum-tx
- tcp6csum, tcp6csum-rx, tcp6csum-tx
- udp4csum, udp4csum-rx, udp4csum-tx
- udp6csum, udp6csum-rx, udp6csum-tx
You can then use
ifconfig
to enable or disable whichever of these options your device supports.
Start io-pkt-v4-hc using the devn-i82544.so driver:
io-pkt-v4-hc -d /lib/dll/devn-i82544.so
ifconfig en0 10.1.0.184
- /dev/io-net
- The directory where, by default, drivers and protocol modules add
entries.
For more information, see the documentation for
io-pkt*
devn-*,
devnp-*,
ifconfig,
io-pkt*
Warning: main(/www/www/htdocs/style/footer.php) [function.main]: failed to open stream: No such file or directory in /www/www/docs/6.4.1/neutrino/utilities/d/devn-i82544.so.html on line 273
Warning: main() [function.include]: Failed opening '/www/www/htdocs/style/footer.php' for inclusion (include_path='.:/www/www/common:/www/www/php/lib/php') in /www/www/docs/6.4.1/neutrino/utilities/d/devn-i82544.so.html on line 273