Warning: main(/www/www/htdocs/style/globals.php) [function.main]: failed to open stream: No such file or directory in /www/www/docs/6.4.1/neutrino/utilities/d/devnp-bcm1250.so.html on line 1
Warning: main() [function.include]: Failed opening '/www/www/htdocs/style/globals.php' for inclusion (include_path='.:/www/www/common:/www/www/php/lib/php') in /www/www/docs/6.4.1/neutrino/utilities/d/devnp-bcm1250.so.html on line 1
Warning: main(/www/www/htdocs/style/header.php) [function.main]: failed to open stream: No such file or directory in /www/www/docs/6.4.1/neutrino/utilities/d/devnp-bcm1250.so.html on line 8
Warning: main() [function.include]: Failed opening '/www/www/htdocs/style/header.php' for inclusion (include_path='.:/www/www/common:/www/www/php/lib/php') in /www/www/docs/6.4.1/neutrino/utilities/d/devnp-bcm1250.so.html on line 8
Driver for Broadcom BCM1250 10/100/1000 Mbit Ethernet controllers
io-pkt-variant -d bcm1250 \
memrange=0xXXXXXXXX,irq=0xYYYYYYYY,\
mac=ZZZZZZZZZZZZ[,option[,option ...]] ... &
where variant is one of v4, v4-hc, or
v6-hc.
Neutrino
|
Use commas, not spaces, to separate the options.
These options override the autodetected defaults. |
- allmulticast
- Always receive all multicast packets.
- cluster=X
- The size of the Rx descriptor data buffers, in bytes.
The default is 2048; 4096 is a good value with the appropriate
io-pkt binary.
- dma64=0|1
- Turn off or on 64-byte DMA transfers.
- duplex=0|1
- Half (0) or full (1) duplex mode.
The default is automatically detected on supported hardware.
You can also use ifconfig -m and
ifconfig bcmX media to set this.
- irq=num
- The IRQ of the interface.
- kermask=0|1
- Specify the masking:
- 1 — use the kernel interrupt-masking methodology.
- 0 — manually mask the NIC in the interrupt handler.
- lockcpu=N
- Set the CPU affinity for the Rx thread to N.
- mac=XXXXXXXXXXXX
- The interface address of the controller.
You must specify this option if you aren't using the syspage
option.
- memrange=XXXXXXXXXXXX
- Register base physical memory address.
- nomulticast
- Disable multicast support.
By default, multicast is enabled.
- probe_phy=0|1
- Disable (0) or force (1) periodic PHY probing when idle.
- promiscuous
- Enable the driver to pass all data packets received, regardless of the
address.
By default, promiscuous mode is disabled.
- receive=num
- The number of Rx buffers to internally cache.
The default is 512.
- speed=10|100|1000
- The media data rate in megabits/second.
The default is automatically detected on supported hardware.
You can also use ifconfig -m and
ifconfig bcmX media to set this.
- syspage
- Read hardware parameters (IRQs, MAC, base register address, and
PHY address) for all devices from the system page.
If you don't use this option, you must use the mac=X
option.
- transmit=num
- The number of Tx buffers to internally cache.
The default is 1024.
- tx_rd=N
- Set the TX_RD threshold.
- tx_rl=N
- Set the TX_RL threshold.
- verbose
verbose=N
- Be verbose.
Specify num for more verbosity (num can be 1-4;
the higher the number, the more detailed the output).
The default is 0.
The output goes to
slogger;
invoke
sloginfo
to view it.
The devnp-bcm1250.so driver controls
Broadcom BCM1250 10/100/1000 Mbit Ethernet controllers.
This is a native io-pkt driver;
its interface names are in the form bcmX, where
X is an integer.
Some devices support hardware checksums, although some might do so in
only one direction; to determine if your device does, type:
ifconfig bcmX
and look for the following in the list of supported options:
- ip4csum, ip4csum-rx, ip4csum-tx
- tcp4csum, tcp4csum-rx, tcp4csum-tx
- tcp6csum, tcp6csum-rx, tcp6csum-tx
- udp4csum, udp4csum-rx, udp4csum-tx
- udp6csum, udp6csum-rx, udp6csum-tx
You can then use
ifconfig
to enable or disable whichever of these options your device supports.
Start the v4 TCP/IP variant of io-pkt using the
devnp-bcm1250.so driver on BCM91480A eth0:
io-pkt-v4 -d /proc/boot/devnp-bcm1250.so \
memrange=0x10064000,irq=0x80050024,mac=001122334455
ifconfig bcm0 10.184
devn-*,
devnp-*,
ifconfig,
io-pkt
Warning: main(/www/www/htdocs/style/footer.php) [function.main]: failed to open stream: No such file or directory in /www/www/docs/6.4.1/neutrino/utilities/d/devnp-bcm1250.so.html on line 248
Warning: main() [function.include]: Failed opening '/www/www/htdocs/style/footer.php' for inclusion (include_path='.:/www/www/common:/www/www/php/lib/php') in /www/www/docs/6.4.1/neutrino/utilities/d/devnp-bcm1250.so.html on line 248