Warning: main(/www/www/htdocs/style/globals.php) [function.main]: failed to open stream: No such file or directory in /www/www/docs/6.4.1/neutrino/utilities/d/devnp-mpc85xx.so.html on line 1
Warning: main() [function.include]: Failed opening '/www/www/htdocs/style/globals.php' for inclusion (include_path='.:/www/www/common:/www/www/php/lib/php') in /www/www/docs/6.4.1/neutrino/utilities/d/devnp-mpc85xx.so.html on line 1
Warning: main(/www/www/htdocs/style/header.php) [function.main]: failed to open stream: No such file or directory in /www/www/docs/6.4.1/neutrino/utilities/d/devnp-mpc85xx.so.html on line 8
Warning: main() [function.include]: Failed opening '/www/www/htdocs/style/header.php' for inclusion (include_path='.:/www/www/common:/www/www/php/lib/php') in /www/www/docs/6.4.1/neutrino/utilities/d/devnp-mpc85xx.so.html on line 8
Driver for Freescale MPC85XX TSEC Ethernet controllers
|
This driver is shipped only with the BSPs that need it. |
io-pkt-variant -d mpc85xx mac=ZZZZZZZZZZZZ
[option[,option...]] ... &
where variant is one of v4, v4-hc, or
v6-hc.
Neutrino
|
Use commas, not spaces, to separate the options.
These options override the autodetected defaults. |
- duplex=0|1
- Half (0) or full (1) duplex mode.
The default is automatically detected on supported hardware.
You can also use ifconfig -m and
ifconfig tsecX media to set this.
- etsec=0|1
- Use the older TSEC (0) or newer eTSEC (1).
The default is automatically detected on supported hardware.
- fifo=num
- Set the transmit FIFO threshold to num.
The default is 64 on 85xx, and 480 on 83xx.
Each entry is 4 bytes.
- kermask=0|1
- Specify the masking:
- 1 — use the kernel interrupt-masking methodology.
- 0 — manually mask the NIC in the interrupt handler.
- loopback
- Place the MAC into loopback mode for testing purposes.
- mac=XXXXXXXXXXXX
- The interface address of the controller.
You must specify this option if you aren't using the syspage
option.
- nomulticast
- Disable multicast support.
By default, multicast is enabled.
- pauseignore
- Disable link-layer flow control for Rx.
- pausesuppress
- Disable link-layer flow control for Tx.
- phy_addr=X
- The PHY address that en0 has.
- phy_incr=X
- The PHY address increment to add to get the address for the next interface.
- probe_phy=0|1
- Disable (0) or force (1) periodic PHY probing when idle.
- promiscuous
- Enable promiscuous packet receive mode for debugging.
By default, promiscuous mode is disabled.
- receive=num
- The number of receive descriptors.
The default is 512.
- rx_delay=X
- Set the Rx interrupt coalescing timer threshold.
Valid values are 1 through 65,535; the default is zero (disabled).
If you set rx_delay, you must also set rx_frame.
- rx_frame=X
- Set the Rx interrupt coalescing frame threshold.
Valid values are 1 through 255; the default is zero (disabled).
If you set rx_frame, you must also set rx_delay.
- speed=10|100|1000
- The media data rate in megabits/second.
The default is automatically detected on supported hardware.
You can also use ifconfig -m and
ifconfig tsecX media to set this.
- syspage
- Read hardware parameters (IRQs, MAC, base register address, and
PHY address) for all devices from system page.
If you don't use this option, you must use the mac=X
option.
- transmit=num
- The number of transmit descriptors.
The default is 1024.
- verbose
verbose=N
- Be verbose.
Specify num for more verbosity (num can be 1-4;
the higher the number, the more detailed the output).
The default is 0.
The output goes to
slogger;
invoke
sloginfo
to view it.
The devnp-mpc85xx.so driver controls
Freescale MPC85XX TSEC Ethernet controllers.
This is a native io-pkt driver;
its interface names are in the form tsecX, where
X is an integer.
Some devices support hardware checksums, although some might do so in
only one direction; to determine if your device does, type:
ifconfig tsecX
and look for the following in the list of supported options:
- ip4csum, ip4csum-rx, ip4csum-tx
- tcp4csum, tcp4csum-rx, tcp4csum-tx
- tcp6csum, tcp6csum-rx, tcp6csum-tx
- udp4csum, udp4csum-rx, udp4csum-tx
- udp6csum, udp6csum-rx, udp6csum-tx
You can then use
ifconfig
to enable or disable whichever of these options your device supports.
Start the v4 TCP/IP variant of io-pkt using the
devnp-mpc85xx.so driver:
io-pkt-v4 -d mpc85xx mac=00123456789a
ifconfig tsec0 10.184
devn-*,
devnp-*,
ifconfig,
io-pkt
Warning: main(/www/www/htdocs/style/footer.php) [function.main]: failed to open stream: No such file or directory in /www/www/docs/6.4.1/neutrino/utilities/d/devnp-mpc85xx.so.html on line 262
Warning: main() [function.include]: Failed opening '/www/www/htdocs/style/footer.php' for inclusion (include_path='.:/www/www/common:/www/www/php/lib/php') in /www/www/docs/6.4.1/neutrino/utilities/d/devnp-mpc85xx.so.html on line 262